- This topic has 0 replies, 1 voice, and was last updated 1 year, 2 months ago by .
-
Posts
-
1. Fill gas upside down. Do not fill too full, and do not fill vigorously to avoid leakage.
2. Check leakage. Put Tank into water, to see bubbles.
3. Firstly, put the “Lighter Head Part” lightly on the “Lighter Tank Part”, then the index finger upward continuously lifting the white button, the thumb at the same time downward press the Metal Wind Shield, and finally press the two parts firmly together to assemble them. The lighter is assembled!
4. lighter is ok!
5. When the ignition rate decreases in the future, the “Lighter Head Part” can be disassembled by “rotating” it in one direction as shown in the picture. Replacement with new “Lighter Head Part”.
6. use knife to cut the Adjust Ring into 2 legs
7. Grabbing one leg will be mutually slippery and the flame height can’t be adjusted
8. grabbing 2 legs, the flame height can be adjusted. By grabbing 1 or 2 legs, the flame height can be infinitely adjusted.
9. Thumb nail press the black button in the middle to ignite. Child-safe lighter, prevent children from playing. It is a little difficult to ignite, please understand.
10. Best flame height: the overall height of the flame is equal to the thickness of the device.
The flame mustn’t be big!!
11. insert the lighter into Sleeve according to the pattern, and insert into the Main Body together according to the direction shown in the picture.
12. Screw the cigarette (standard size) into the Threaded Tube like a screw.
13. For the first use, it is necessary to check whether the cigarette insertion depth is correct: the left end of the cigarette is aligned with the “flame tip” (about 2 mm from the holes); The tick mark on the Threaded Pipe at the right end is aligned with the metal shell.
This adjusts the optimal depth of the cigarette into the Threaded Tube. Be sure to learn to align the end of the cigarette with the “flame tip”.
(Important!!!) 14. The Threaded Tube and cigarette are screwed into the Main Body together, and the tick mark on the Threaded Tube are aligned with the Metal Shell.
15. Press the button with thumb, the lighter ignites and the Threaded Tube advances automatically.
Toast for 2 seconds before smoking, then quickly take medium strength suction, stop, suction, stop, suction, stop …… The lips are sealed throughout. Until the smoke is rich enough you can stop and exhale the smoke. Be careful not to have too much richness so as not to cause a high temperature burn that will cause the flavor to suddenly become monotonous. Release the ignition button after smoking, the flame will automatically extinguish and the cigarette will go out. Wait for the “Loong Shell” to cool completely before taking the next smoking, the device needs to rest and to stay cool. It is recommended to use several lighters in turn to allow each lighter to rest and cool sufficiently.(please learn smoking skills detailedly in the video tutorial)
If the lighter does not ignite successfully, wait “at least” 10 seconds for air to flow back into the device before next ignition.
16. Flame pointing upwards, very good.
17. flame pointing forward. Indicates that the flame is too large and needs to be turned down. If the flame is too large, the device will be hot, and the cigarette will not be ignited
18. The flame is too small, it is better to adjust it bigger. Too small flame will result in failure to ignite.
19. Wait 3 minutes after the Threaded Tube reaches the end, open the Silicone Cap on the top and remove the exposed ash.
20. Unscrew out the Threaded Tube, the ash was all taken out.
21. If the ash gets stuck inside, poke out the ash with the inclued straw.
22. Clean the burning side (as shown) with the included brush.
Please clean up frequently, otherwise there will be occasional small sparks falling out.
23. Finally close the Silicone Cap.
24. It is up to you to decide whether to install the Big Hand Handle(tighten the 6 screws in the picture, of which the two screws in the center green circle should be loosened a little).
25. Install the Bottom Cover of the Handle, with the side with text facing outward.
26. When using non-standard sized slim diameter cigarettes, please install Adapter. And make sure to check according to Clause 13 to feed the end of the cigarette to the “Flame Tip”.
27. Insert Child Safety Lighter into “Jurchen Iron Case”, it will become to a normal lighter.
28. For branded cigarette, please knock the filter onto the table until the tobacco in the blue circle in the picture sinks. This increases the support of the red-circled part next to the filter and prevents clogging.
29. Then tear off the excess paper.
30. Hand rolled cigarette: The filter should be short to increase suction resistance and enhance flavor. The red circle next to the filter in the above picture should be filled with more tobacco to increase suction resistance, flavor, and support (to prevent blockage). In the green circle far away from the filter in the above picture, do not put too much tobacco to increase breathability and prevent blockage after expansion. The roll paper must be absorbent, and non-absorbent oiled paper (slow-burning paper) cannot be used. It is highly recommended to watch the video tutorial!
31. The overall diameter of the hand-rolled cigarette should be uniform and not thick(if too thick, it will get clogged), and the red circle part should be relatively hard; The green circle part should be soft and elastic.
This device is used for international standard cigarette size by default. About the use of hand rolled cigar leaf, hand rolled pipe tobacco and other high level skills, please study in our other instructions. You can leave your questions in this forum, we will reply as soon as possible.
- This topic was modified 1 year, 2 months ago by .
- This topic was modified 1 year, 2 months ago by .
- This topic was modified 1 year, 2 months ago by .
- This topic was modified 1 year, 2 months ago by .
- This topic was modified 11 months, 2 weeks ago by .
- This topic was modified 11 months, 2 weeks ago by .
- This topic was modified 11 months, 2 weeks ago by .
- This topic was modified 11 months, 2 weeks ago by .
- This topic was modified 11 months, 1 week ago by .
- This topic was modified 11 months, 1 week ago by .
- This topic was modified 11 months, 1 week ago by .
- This topic was modified 9 months, 2 weeks ago by .
- This topic was modified 9 months, 2 weeks ago by .
- This topic was modified 8 months, 1 week ago by .
- This topic was modified 7 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 5 months, 1 week ago by .
- This topic was modified 4 months ago by .
- This topic was modified 3 months ago by .
- You must be logged in to reply to this topic.